Off Topic Forum (Archived)
Compressors what/which one do I need
Posted by Tasng4
Topic Creator (OP)
Dec 9, 2016 04:21 AM
Joined 9 years ago
35 Posts
|
Hi,
Can anyone help me decide what type/power/capacity of compressor I should buy?
For years I've been using 3 X 25ltr compressors connected in parallel, one of them has now died so I want to replace all of them with something which can handle blast cleaning. Previously I could blast for 30 seconds and them have to wait for 1.5 mins for the tanks to recharge.
I want to buy a compressor which can keep us with the amount of air blast cleaning uses. None of the tech specs seem to give the information I'm looking for. I know blast cleaning uses about 9cfm so ideally I want a compressor that can recharge faster than I'm using air - if that's possible. Also I only have a normal 2 phase supply (N.B. I'm in France where we use 230 volts.)
I really don't want to buy the wrong thing.
Thanks.
Can anyone help me decide what type/power/capacity of compressor I should buy?
For years I've been using 3 X 25ltr compressors connected in parallel, one of them has now died so I want to replace all of them with something which can handle blast cleaning. Previously I could blast for 30 seconds and them have to wait for 1.5 mins for the tanks to recharge.
I want to buy a compressor which can keep us with the amount of air blast cleaning uses. None of the tech specs seem to give the information I'm looking for. I know blast cleaning uses about 9cfm so ideally I want a compressor that can recharge faster than I'm using air - if that's possible. Also I only have a normal 2 phase supply (N.B. I'm in France where we use 230 volts.)
I really don't want to buy the wrong thing.
Thanks.
|
Dec 9, 2016 07:21 AM
Top Contributor
Joined 17 years ago
9,570 Posts
|
Properly sizing a compressor for a sandblasting job means considering both the PSI (pounds per square inch) and CFM (cubic feet per minute) of the compressor. The two factors together determine the total supply the compressor is capable of providing. The CFM on the compressor needs to be higher than that of the blaster. Choose a two-stage compressor with five horsepower or more and at least 80 gallons to ensure that the compressor runs in intervals instead of continually.
Dec 9, 2016 07:34 AM
Joined 10 years ago
337 Posts
|
In reply to # 3408981 by Paul J
Choose a two-stage compressor with five horsepower or more and at least 80 gallons to ensure that the compressor runs in intervals instead of continually.
Hello Neil,
I bought a 60-gallon, 3-horsepower, 2-stage compressor and it is not quite large enough for my blasting cabinet. Paul's suggestion seems right to me.
Good luck,
Earl
Forum: (fo·rum)
1. a place, meeting, or medium where ideas and views on a particular issue can be exchanged.
Edited 1 time(s). Last edit at 2016-12-09 08:12 AM by ebooks76B.
Topic Creator (OP)
Dec 9, 2016 07:38 AM
Joined 9 years ago
35 Posts
|
This is the one I'm thinking about --> https://www.machinemart.co.uk/p/clarke-boxer-14200-200-litre-belt-driven-air/
Earl - I realise it's nearer yours than what Paul suggests but there is a cost element as well. I expect, mostly, to be blasting smaller parts with regular pauses.
Thanks for the advice.
Earl - I realise it's nearer yours than what Paul suggests but there is a cost element as well. I expect, mostly, to be blasting smaller parts with regular pauses.
Thanks for the advice.
Dec 9, 2016 04:30 PM
Joined 15 years ago
4,348 Posts
|
You will need to select the sand blasting equipment, and then determine which air compressor you will need, knowing what the sand blasting equipment needs.
Yes, it is the only way to clean "old car parts, down to bare metal."
When I had this equipment, we lived in a rural area, away from other homes. If you are in an urban area, your neighbors WON'T LIKE THE NOISE!
Roger N. Tanner
Professional Engineer, Retired
Yes, it is the only way to clean "old car parts, down to bare metal."
When I had this equipment, we lived in a rural area, away from other homes. If you are in an urban area, your neighbors WON'T LIKE THE NOISE!
Roger N. Tanner
Professional Engineer, Retired
Dec 9, 2016 06:12 PM
Top Contributor
Joined 14 years ago
19,079 Posts
|
In reply to # 3409320 by rntanner
You will need to select the sand blasting equipment, and then determine which air compressor you will need, knowing what the sand blasting equipment needs.
If you are in an urban area, your neighbors WON'T LIKE THE NOISE!
If you are in an urban area, your neighbors WON'T LIKE THE NOISE!
X2000
Michael J. Caputo
'79, '77, '76, '74.5 (rubber dual SU), and '73 owner. Extensive experience in 12v Audio System design and installation. Vendor of Regalia and Promotional Products since 1993. Supplier of Accessories to MOSS. Forum Member since 2009; with a warped sense of humor since birth. Publisher of the annual MGB & GT Calendar, mailed worldwide.
Member Services:
Please send photos for next year's calendar to photos25@mgbcalendar.com. If you need help with your Weber downdraft carburetor, feel free to call me at 978-249-5760, USA, Central Time!
Dec 9, 2016 06:50 PM
Top Contributor
Joined 13 years ago
7,596 Posts
|
You may want to get an upright tank to save space. plus it won't hurt to install it out side your garage in an enclosed area. That will cut down in the noise in our shop. If your going to sand blast or paint I suggest you either buy a dryer for the compressor or make one. Your going to get a lot of moisture/water mixing with your sand or paint.
John
John
Dec 9, 2016 07:57 PM
Joined 19 years ago
6,502 Posts
|
mgbanthony
Anthony Henderson
|
Dec 10, 2016 11:30 PM
Top Contributor
Joined 18 years ago
13,239 Posts
|
Topic Creator (OP)
Dec 11, 2016 11:40 AM
Joined 9 years ago
35 Posts
|
Yes I accept that the compressor could/will struggle a bit but I have to weigh up the pros & cons of spending more for a REAL MAN'S compresssor or buying a smaller one which will be cheaper but will cope. For the last 10 years I have been using 3 X 25ltr compressors. I don't do much blasting but I'm just starting a restoration (sorry not an MG) and foresee the amount of blasting rising.
Regards,
Regards,
Sorry, you do not have permission to post in this forum. The forum may be locked (archived).
Forums
Having trouble posting or changing forum settings?
Read the Forum Help (FAQ) or contact the webmaster